You have no items in your shopping cart.
Need to make your new sata drive fit into an older computer with no sata ports and only IDE 40 pin cable Connection?
NO DRIVERS NEEDED JUST PLUG AND PLAY!
Here is a simple and easy adapter, just plug it into any sata I or sata II hard drive and walla, you have now made your sata drive into an IDE 40pin standard connection drive.
Native SATA Drive to IDE 40-pin Adapter for Most Enclosures
SATA to IDE Converter - Converts SATA Drive to IDE
A perfect solution for converting SATA or SATA II devices to IDE ATA 40-Pin UDMA-133/100 interfaces
JMicron JM20330 chip-set and supports 3.5" IDE hard drives and 5.25" optical drives. It's compliant with IDE specification and supports up to UDMA/133 drives!
About The Chip
Overview
The JM20330 is a single chip solution for serial and parallel ATA translation. It includes the Serial ATA PHY, Link, Transport, and Parallel ATA (application layer) controller. The Serial ATA physical, link, and transport layers are compliant to Serial ATA 1.0 JM20330 supports a 1.5GHz data rate, and scalable to 3.0 GHz data rate by directly doubling the internal clock source. The application layer supports both the ATA register command set and PACKET command set, which could drive both Hard Disk Drive and ATAPI Optical Storage such as CR-ROM, CD-RW, DVD-ROM, DVD-RW, etc. The Serial ATA and the Parallel ATA application layer support both host and device operation and can be configured through a single pin.
Feature Compliance
• Serial ATA 1.0 Specification compliant
Overall
• Automatic Serial ATA 3.0/1.5 Gbps speed negotiation
• ATA/ATAPI PIO mode 0 to 4
• ATA/ATAPI Ultra DMA of transfer rate 16.7, 25, 33, 48, 66, 100, 133, and 150MB/s.
• ATA/ATAPI LBA48 addressing mode associated with 2-byte sector count
• Support Serial ATA hot-plug
• Ultra low power consumption
• Work for both AC and DC couple between the transmitter and the receiver
• Provide specified OOB signal detection and transmission
• Support Spread Spectrum Clocking to reduce EMI
• Support 20MHz, 25MHz, 30MHz or 40MHz Reference Clock
• Support Partial/Slumber power management
• Provide adjustable TX signal amplitude and pre-emphasis level
• Master IDE Device support
Product Requirements:
Windows 98/SE/ME/2000/XP/2003/Vista/Linux operating system
Available 4-pin power supply connector
SATA I or SATA II Device
OPERATING SYSTEMS SUPPORT
Windows 98
Windows NT 4.0
Windows 2000
Windows 2003
Windows Me
Windows XP
Windows Vista 32-bit and 64-Bit
Linux
MAC OS X
IDE-SATA04 Jumper Information
The SATA to IDE adapter can be used on an IDE ribbon cable with another device. There are two possible configurations. You can use the adapter as the Master device, or Slave device.
New Low Profile Version Started to ship in Mid July 2008, Very Small PCB fit all 3.5 Inch and 2.5 inch SATA Hard Drives. This is what the New Unit Now Looks Like!
********
Anonymous Customer Rating: Excellent
Price Rating:Excellent
Shipping Options Rating:Excellent
Delivery Rating:Excellent
Ease of Purchase Rating:Excellent
Customer Service Rating:Excellent
Title:
Body:I purchased the SATA Hard Drive Adapter to IDE ATA-100/133 40 Pin Cable http://www.cooldrives.com/sahadradtoid.html
Regular price: $27.98 - Sale Price $17.88
The product worked exactly as described. It was very easy to install. It arrived at my door lightning fast. Packaging was great. This product was exactly what I needed. I am very satisfied with my purcahse and would do business with CoolDrives.com again.
Thank You CoolDrives.com!
NO DRIVERS NEEDED JUST PLUG AND PLAY!
Here is a simple and easy adapter, just plug it into any sata I or sata II hard drive and walla, you have now made your sata drive into an IDE 40pin standard connection drive.
Click on Video To Play SATA HDD to IDE Adapter Video
Native SATA Drive to IDE 40-pin Adapter for Most Enclosures
SATA to IDE Converter - Converts SATA Drive to IDE
A perfect solution for converting SATA or SATA II devices to IDE ATA 40-Pin UDMA-133/100 interfaces
JMicron JM20330 chip-set and supports 3.5" IDE hard drives and 5.25" optical drives. It's compliant with IDE specification and supports up to UDMA/133 drives!
This Adapter tested to work with Western Digital, Seagate, Hitachi, Maxtor, Toshiba, Fujitsu and Samsung Drives ranging in Capacity from 80GB up to 2,500GB (2.5TB).
About The Chip
Overview
The JM20330 is a single chip solution for serial and parallel ATA translation. It includes the Serial ATA PHY, Link, Transport, and Parallel ATA (application layer) controller. The Serial ATA physical, link, and transport layers are compliant to Serial ATA 1.0 JM20330 supports a 1.5GHz data rate, and scalable to 3.0 GHz data rate by directly doubling the internal clock source. The application layer supports both the ATA register command set and PACKET command set, which could drive both Hard Disk Drive and ATAPI Optical Storage such as CR-ROM, CD-RW, DVD-ROM, DVD-RW, etc. The Serial ATA and the Parallel ATA application layer support both host and device operation and can be configured through a single pin.
Feature Compliance
• Serial ATA 1.0 Specification compliant
Overall
• Automatic Serial ATA 3.0/1.5 Gbps speed negotiation
• ATA/ATAPI PIO mode 0 to 4
• ATA/ATAPI Ultra DMA of transfer rate 16.7, 25, 33, 48, 66, 100, 133, and 150MB/s.
• ATA/ATAPI LBA48 addressing mode associated with 2-byte sector count
• Support Serial ATA hot-plug
• Ultra low power consumption
• Work for both AC and DC couple between the transmitter and the receiver
• Provide specified OOB signal detection and transmission
• Support Spread Spectrum Clocking to reduce EMI
• Support 20MHz, 25MHz, 30MHz or 40MHz Reference Clock
• Support Partial/Slumber power management
• Provide adjustable TX signal amplitude and pre-emphasis level
• Master IDE Device support
Product Requirements:
Windows 98/SE/ME/2000/XP/2003/Vista/Linux operating system
Available 4-pin power supply connector
SATA I or SATA II Device
OPERATING SYSTEMS SUPPORT
IDE-SATA04 Jumper Information
The SATA to IDE adapter can be used on an IDE ribbon cable with another device. There are two possible configurations. You can use the adapter as the Master device, or Slave device.
New Low Profile Version Started to ship in Mid July 2008, Very Small PCB fit all 3.5 Inch and 2.5 inch SATA Hard Drives. This is what the New Unit Now Looks Like!
********
Anonymous Customer Rating: Excellent
Price Rating:Excellent
Shipping Options Rating:Excellent
Delivery Rating:Excellent
Ease of Purchase Rating:Excellent
Customer Service Rating:Excellent
Title:
Body:I purchased the SATA Hard Drive Adapter to IDE ATA-100/133 40 Pin Cable http://www.cooldrives.com/sahadradtoid.html
Regular price: $27.98 - Sale Price $17.88
The product worked exactly as described. It was very easy to install. It arrived at my door lightning fast. Packaging was great. This product was exactly what I needed. I am very satisfied with my purcahse and would do business with CoolDrives.com again.
Thank You CoolDrives.com!
| SKU | SATAIDE-2as |
| Manufacturer | CoolGear |
